
Start with a device list, not a port count
The right network switch for an office is the one sized from your device list: a port for every wired device, enough power for every device the switch feeds, and uplinks fast enough for everything behind them. This guide works through that sizing before you compare Cisco network switches in Dubai or any other brand.
Go through the floor plan and list everything that needs a cable: computers, phones, printers, cameras, door controllers and office Wi-Fi access points. Laptops and mobiles on Wi-Fi use no switch port, but their access point does. Mark each device that takes its power from the switch.
Here is the count for a made-up office of 16 desks. It is an example only, not a design for your site.
| Device (example office) | Needs PoE | Ports |
|---|---|---|
| Desk computers | No | 16 |
| IP desk phones | Yes | 4 |
| Network printers | No | 2 |
| Wi-Fi access points | Yes | 3 |
| IP cameras | Yes | 8 |
| Door controllers | Yes | 2 |
| CCTV recorder (NVR) | No | 1 |
| Internet router or firewall | No | 1 |
| Ports in use | 17 with PoE | 37 |
| Spare on a 48-port switch | 11 |
Thirty-seven ports fit one 48-port switch with 11 spare, or two 24-port switches: one with PoE for the 17 powered devices, one without for the other 20. Keep spare ports either way, so a new hire or an extra camera does not mean another switch.
PoE: standards and the power budget
Power over Ethernet (PoE) means the switch sends power down the same network cable that carries the data, so a camera or access point on the ceiling needs no power socket.
The three common standards
- IEEE 802.3af (PoE): up to 15.4 W at the switch port.
- IEEE 802.3at (PoE+): up to 30 W at the switch port.
- IEEE 802.3bt: up to 60 W or 90 W at the switch port, depending on the type.
The device receives a little less, because some power is lost along the cable. A device built for a higher standard may not start, or may run in a reduced mode, on a lower-standard port.
Why the total budget matters more
The PoE budget is the total wattage a switch can supply across all its ports at once, and it is often less than the port count suggests: 24 PoE+ ports do not guarantee 24 × 30 W. When devices ask for more than the budget, the switch refuses power to some ports and those devices stay off.
Adding up the budget
- List every PoE device and the standard it needs.
- Take each device's maximum power draw from its datasheet, or the ceiling of its standard if you do not have it yet, and multiply by the quantity.
- Add the lines together, allow headroom for devices you expect to add, then compare the total with the switch's PoE budget.
In the example office, suppose the eight cameras are Matrix SATATYA MIDR20FL mini dome cameras at about 7 W each on 802.3af: about 56 W. Three access points and two door controllers at the PoE+ ceiling of 30 W add 150 W. Four phones, assumed to be 802.3af devices at the 15.4 W ceiling, add 61.6 W. The worst case is about 268 W, so the switch needs a budget comfortably above that. We calculate the real figure from your device list before recommending a model.
Uplinks: copper, SFP and SFP+
An uplink is the port that connects a switch to the rest of the network: another switch or the router. Everything plugged into the switch shares that link, so it should be at least as fast as the ports it serves.
Copper uplinks are ordinary RJ45 ports. SFP and SFP+ ports are slots that take a small plug-in module, usually for fibre: SFP for 1 Gbps and SFP+ for 10 Gbps. The module has to match the fibre, multimode or single-mode, at both ends.
A fibre uplink makes sense when:
- the run between two racks is longer than the 100 metres a copper network cable can cover
- the link joins floors, comms rooms or separate buildings
Choose SFP+ when many users, cameras or access points share one uplink. Our comparison of Cat6, Cat6A and fibre covers the cable side.
About the term "fibre switch". People searching for one usually mean this: an ordinary Ethernet switch with SFP or SFP+ ports for fibre.
Managed or unmanaged
Choose a managed switch if anything in the office should be kept apart from staff computers. An unmanaged switch has no settings, so every device plugged into it lands on the same network. A managed switch is configured, usually for three reasons:
- VLANs. One switch is divided into separate networks, so guest Wi-Fi, CCTV and payment terminals stay away from staff computers. It is how we plan network cabling and IT infrastructure for offices.
- 802.1X. A device has to identify itself before its port lets it onto the network, so an unknown laptop in a meeting room socket gets no access.
- Monitoring. The switch reports which ports are up, how much power each PoE port draws and where errors appear.
An unmanaged switch is acceptable in a very small office with nothing to separate: a few computers and a printer, and no cameras, guest Wi-Fi or payment terminals.
Stacking, growth and Layer 2 or Layer 3
Stacking joins two or more switches so they are managed as one: the tidy way to go past 48 ports in one rack. If the office may add a team or a floor, check that the model stacks and leave rack space for the next switch.
A Layer 2 switch moves traffic within each VLAN and leaves traffic between VLANs to the router or firewall. A Layer 3 switch can route between VLANs itself. For a small office, Layer 2 is normally enough. Layer 3 suits larger networks with heavy traffic between VLANs.
Where the switch will live
Decide the location before the model, because it sets the space, the cooling and the power available.
- Rack. Mount the switch directly below its patch panel, with a cable manager between them and short patch cords, as we do on structured cabling jobs in Dubai.
- Ventilation. A switch turns part of its power into heat, and a PoE switch more so. Keep it out of sealed cupboards and ceiling voids, and check that the room's air conditioning stays on outside office hours.
- UPS. A UPS feeding the PoE switch keeps cameras, phones, access points and door controllers running through a short power cut. Size it for the switch and its PoE load.
- Labelled patching. Outlet, patch panel port and drawing should carry the same number, with a port map showing what is on each switch port.
Cisco Catalyst as an example
The Cisco Catalyst 1000, 1200 and 1300 series we supply cover these choices in one range: 8 to 48 Gigabit Ethernet ports, SFP and SFP+ uplinks (1 Gbps and 10 Gbps) and PoE+ budgets of up to 740 W, depending on the model. They are managed by command line, web page or SNMP, support 802.1X, access control lists and DHCP snooping, and stack on selected models.
The example office points to the 48-port end of that range with PoE+, or to a PoE and a non-PoE Cisco switch side by side. We confirm the exact model for each location on the quote, and configure it rather than leave it on factory settings, with a port map and configuration backup at handover.
What to send for a quote
Three things are enough for us to size the switches and quote supply, configuration and installation:
- Floor plan with desks, meeting rooms, cameras, access points and doors with readers marked.
- Device list laid out like the table above, with makes and models where you know them.
- Rack locations: where the comms room or cabinet is on each floor, what is already in it and roughly how far apart the racks are.
Add any switches you already own and want to keep, and the staff or floors you expect to add. Whether the switches are for one floor or a whole building, that is enough for a first design.
Questions
Will a PoE switch damage a computer or printer that does not use PoE?
No. A standards-based PoE switch checks whether the connected device asks for power before it supplies any, so a computer or printer on a PoE port receives data only.
Is a Gigabit switch fast enough for an office?
For desk computers, phones, printers and cameras, a 1 Gbps port is normally enough. The links that benefit from 10 Gbps are the uplinks between switches and the connections to servers or storage.
Do CCTV cameras need their own switch?
Not always. On a managed switch the cameras can share the hardware with the office and sit on their own VLAN. A separate PoE switch makes sense when the cameras are far from the main rack or their power would use up the PoE budget.
What is the difference between a switch and a router?
A switch connects the devices inside your office to each other. A router connects the office network to other networks, such as the internet, and usually sits between the switch and your internet provider's line.